Automation Solutions

We offer Substation Automation Solutions for Chemical Industries for boosting the efficiency of operations and avoiding unnecessary breakdowns.  We also provide training in our new installation for operation and maintenance staff of client to better understanding technology, thus increasing the plant efficiency. 

Our Substation Automation Solutions for Chemical Industries are as follows: 

Engineering Solutions:

•  Auto Transfer Scheme for Incomer and DG switchover 

A bus transfer system is designed to provide process continuity to the loads attached to a motor bus while transferring the bus from one source to another. A successful bus transfer under contingent conditions provides immense value and benefits to continuous process operations that cannot afford an interruption of power supply to plant auxiliaries. 

We are experienced in designing and implementing such schemes for substations.  This can be done as a retrofit in existing panels or supplied as a new panel as per station condition and requirement.

• Load Shedding scheme

During overloads in the mains, the load shedding applied to interruptible loads is often the only solution to keep the industries in operation. Normally, in such cases, non-critical loads that are earlier identified are tripped automatically to avoid interruption of critical loads and induced penalties when power is being drawn from the grid. 

We offer a range of products and solutions from Siemens/Schneider for these critical operations based on Current, Power or frequency for load shedding.

• Power System Studies and Relay Coordination’s

Relay coordination study and analysis is performed to make sure that safety operation of the system are functioning correctly and to avoid the nuisance tripping, as protection is a major concern in any industry and they rely on protective devices for the same. 

        The aim of a coordination study is to determine the characteristics, ratings, and settings of overcurrent protective devices which will ensure that minimum unfaulty load is interrupted when protective devices isolate a fault or overload anywhere in the system.

• Protection System Upgradation/ Retrofits with Modern Numerical Relays

Older relay usually outdated, are supposed to be replaced in industries to avoid mal tripping and ease operations in a plant. We offer 

1. Replacement of old Electromechanical Relays with Numerical Relays
2. Replacement of Outdated Numerical Relays with Latest Models
3. Upgradation of existing SCADA system
4. Integration of additional Devices into existing SCADA

            Our team is experienced in carrying out such services in all types of industries, from data collection, to upgradation and handing over. 

• Outage Loss Monitoring meters

Outages can cause losses in an industry. These outages are often classified as Controlled outage (normal shutdown) or uncontrolled outage (fault trip). Our meters are specifically designed to register such outages in Minutes or seconds and report to automation system. This helps in evaluation of losses on per day, per month or per year basis. 

We are the leading Service Providers for Automation/Scada solutions & their testing.

It’s Time to Transform Your Projects and Operations: 

Many of the industry’s standard approaches were created decades ago, long before today’s innovation. Doing more of the same is yielding only incremental benefits and management expects you to deliver better results. With a partner like Siemens/ABB/ALSTOM, you can. Our automation expertise – from projects to operations – is focused on helping you hit your targets and move your organization into Top Quartile performance.

You need a partner with the expertise and track record to deliver predictable success.

We’re ready to put our industry-tailored experience and solutions to work for you.

Power Generation:-

Today’s operational realities are making it more difficult to achieve your business objectives.

As a power producer, you’re facing dynamic times. Renewables, plant cycling, regulatory compliance and an evolving workforce are all making it more difficult for you to achieve your business objectives. It’s because of these challenges that more and more power producers are turning to Siemens/ABB/Alstom. Our team of power industry experts work with you to enhance your operational readiness – improving plant availability and flexibility while also enhancing workforce proficiency and productivity.

Industrial Energy

Stable utility operations are needed to support all production. Energy is a large part of your operating costs and emissions constraints are increasing. With Emerson’s help you can make utility performance reliable and responsive, improve efficiency, maximize low cost fuel use, and lower emissions… all at the same time.

we offer an industry-leading suite of substation controllers and switches that support a variety of substation control, communication, monitoring, protection and automation applications and functions.

 Reliable transmission and distribution of electricity is the key to a Smart Grid and an integral requirement for Utilities. Substation Automation Systems (SAS) as a comprehensive part of substation control and monitoring solution provides functions such as advanced power system management and monitoring of the condition of the equipment while as service.

Power, a non-renewable source of energy is one of the most focused industries today. For systematic power distribution, power has to be healthy. At every substation level the parameters are checked to determine the condition of power. These parameters go through different stages of checking, rectifying, controlling, etc which are performed at substation level. To integrate all these functions in a system & to perform simultaneous checks, substation automation systems are brought in concept.

We are the leading enablers of  substation  automation  solutions  including  IEC 61850 /104 /101 /103/61850 & Modbus. Our substation automation offerings comply with IEC 61850 standard,, ensuring key to protection, control, automation, monitoring and real-time communications capabilities of substations with existing legacy as well as systems for future. Our smart automation reduces operational and maintenance costs, thereby increasing the performance of the plant and improving the efficiency in operations.

We offer Substation Automation Solutions for Garments Industries for Industries for boosting the efficiency of operations and avoiding unnecessary breakdowns.  We also provide training in our new installation for operation and maintenance staff of client to better understanding technology, thus increasing the plant efficiency. 

Our Substation Automation Solutions for Garments industries are as follows: 

Engineering Solutions:

•  Auto Transfer Scheme for Incomer and DG switchover 

A bus transfer system is designed to provide process continuity to the loads attached to a motor bus while transferring the bus from one source to another. A successful bus transfer under contingent conditions provides immense value and benefits to continuous process operations that cannot afford an interruption of power supply to plant auxiliaries. 

We are experienced in designing and implementing such schemes for substations.  This can be done as a retrofit in existing panels or supplied as a new panel as per station condition and requirement.

• Load Shedding scheme

During overloads in the mains, the load shedding applied to interruptible loads is often the only solution to keep the industries in operation. Normally, in such cases, non-critical loads that are earlier identified are tripped automatically to avoid interruption of critical loads and induced penalties when power is being drawn from the grid. 

We offer a range of products and solutions from Siemens/Schneider for these critical operations based on Current, Power or frequency for load shedding.

• Power System Studies and Relay Coordination’s

Relay coordination study and analysis is performed to make sure that safety operation of the system are functioning correctly and to avoid the nuisance tripping, as protection is a major concern in any industry and they rely on protective devices for the same. 

        The aim of a coordination study is to determine the characteristics, ratings, and settings of overcurrent protective devices which will ensure that minimum unfaulty load is interrupted when protective devices isolate a fault or overload anywhere in the system.

• Protection System Upgradation/ Retrofits with Modern Numerical Relays

Older relay usually outdated, are supposed to be replaced in industries to avoid mal tripping and ease operations in a plant. We offer 

1. Replacement of old Electromechanical Relays with Numerical Relays
2. Replacement of Outdated Numerical Relays with Latest Models
3. Upgradation of existing SCADA system
4. Integration of additional Devices into existing SCADA

Our team is experienced in carrying out such services in all types of industries, from data collection, to upgradation and handing over. 

• Outage Loss Monitoring meters

Outages can cause losses in an industry. These outages are often classified as Controlled outage (normal shutdown) or uncontrolled outage (fault trip). Our meters are specifically designed to register such outages in Minutes or seconds and report to automation system. This helps in evaluation of losses on per day, per month or per year basis. 

We offer Substation Automation for RMG Industries for boosting the efficiency of operations and avoiding unnecessary breakdowns.  We also provide training in our new installation for operation and maintenance staff of client to better understanding technology, thus increasing the plant efficiency. 

Substation Automation for RMG Industries solutions are as follows: 

Engineering Solutions:

•  Auto Transfer Scheme for Incomer and DG switchover 

A bus transfer system is designed to provide process continuity to the loads attached to a motor bus while transferring the bus from one source to another. A successful bus transfer under contingent conditions provides immense value and benefits to continuous process operations that cannot afford an interruption of power supply to plant auxiliaries. 

We are experienced in designing and implementing such schemes for substations.  This can be done as a retrofit in existing panels or supplied as a new panel as per station condition and requirement.

• Load Shedding scheme

During overloads in the mains, the load shedding applied to interruptible loads is often the only solution to keep the industries in operation. Normally, in such cases, non-critical loads that are earlier identified are tripped automatically to avoid interruption of critical loads and induced penalties when power is being drawn from the grid. 

We offer a range of products and solutions from Siemens/Schneider for these critical operations based on Current, Power or frequency for load shedding.

• Power System Studies and Relay Coordination’s

Relay coordination study and analysis is performed to make sure that safety operation of the system are functioning correctly and to avoid the nuisance tripping, as protection is a major concern in any industry and they rely on protective devices for the same. 

        The aim of a coordination study is to determine the characteristics, ratings, and settings of overcurrent protective devices which will ensure that minimum unfaulty load is interrupted when protective devices isolate a fault or overload anywhere in the system.

• Protection System Upgradation/ Retrofits with Modern Numerical Relays

Older relay usually outdated, are supposed to be replaced in industries to avoid mal tripping and ease operations in a plant. We offer 

1. Replacement of old Electromechanical Relays with Numerical Relays
2. Replacement of Outdated Numerical Relays with Latest Models
3. Upgradation of existing SCADA system
4. Integration of additional Devices into existing SCADA

            Our team is experienced in carrying out such services in all types of industries, from data collection, to upgradation and handing over. 

• Outage Loss Monitoring meters

Outages can cause losses in an industry. These outages are often classified as Controlled outage (normal shutdown) or uncontrolled outage (fault trip). Our meters are specifically designed to register such outages in Minutes or seconds and report to automation system. This helps in evaluation of losses on per day, per month or per year basis.